EndoLab - Implant Testing Services Implant Testing

Wirbelsäulenimplantate
 

Wirbelsäulenimplantate - Komponenten - ASTM F2193Wirbelsäulenimplantate - Komponenten - ASTM F2193 Wirbelsäulenimplantate - Verbindungs- und Teilkonstrukte - ASTM F1798Wirbelsäulenimplantate - Verbindungs- und Teilkonstrukte - ASTM F1798 Korpektomie Modell - ASTM F1717Korpektomie Modell - ASTM F1717 Fusionsimplantate - ASTM F2077Fusionsimplantate - ASTM F2077 Verschleißversuch - ISO 18192-1Verschleißversuch - ISO 18192-1 Einsinkverhalten - ASTM F2267Einsinkverhalten - ASTM F2267 Nucleusimplantate - ISO 18192-2Nucleusimplantate - ISO 18192-2 Expulsion Test - PI-52Expulsion Test - PI-52 Korpektomie Modell mit anteriorer Unterstützung - ISO 12189Korpektomie Modell mit anteriorer Unterstützung - ISO 12189 Extra diskale bewegungserhaltenden Wirbelsäulenimplantate - ASTM F2624Extra diskale bewegungserhaltenden Wirbelsäulenimplantate - ASTM F2624 Prüfung von Facettengelenkimplantaten - ASTM F2694/F2790Prüfung von Facettengelenkimplantaten - ASTM F2694/F2790 Okzipital-zervikale und Okzipital-zervikale-thorakale Modelle - ASTM F2706Okzipital-zervikale und Okzipital-zervikale-thorakale Modelle - ASTM F2706 Dornfortsatzplatten - PI-76Dornfortsatzplatten - PI-76 Prüfung von Nucleusimplantaten nach - ASTM F2789Prüfung von Nucleusimplantaten nach - ASTM F2789 Impingement Test für lumbale ProthesenImpingement Test für lumbale Prothesen Spezielle Anforderungen an Gelenkimplantate - ISO 21534Spezielle Anforderungen an Gelenkimplantate - ISO 21534 Impingement wear testing of total disc prostheses - ASTM F3295Impingement wear testing of total disc prostheses - ASTM F3295 Bandscheibenimplantate - ASTM F2346Bandscheibenimplantate - ASTM F2346 Präklinische Testung von Wirbelkörperimplantaten (cage) - ISO 23089-2Präklinische Testung von Wirbelkörperimplantaten (cage) - ISO 23089-2

Korpektomie Modell - ASTM F1717

Aktuelle Prüfverfahren  



ASTM F1717: Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model.

These test methods cover the materials and methods for the static and fatigue testing of spinal implant assemblies in a vertebrectomy model. The appropriate tests within the standard have to be selected depending on the implant system and its intended spinal location and application method.

Static and dynamic loading is performed for the worst-case scenario. Load transfer between the resection lines has to be guaranteed by the implant without bone support. Two UHMWPE blocks are used for implant fixation. The dynamic loading is performed at a frequency of 5 Hz and at up to 5 million cycles. In general, six specimens are tested. Regular tests are performed in air at room temperature. The implant material may require test setups simulating body environmental conditions at 37 °C in saline solution.
The standard describes the following test procedures: Static and dynamic axial compression bending, static tension bending, and static torsion. This standard is applicable to lumbar and cervical systems.  


Implant Testing - Korpektomie Modell - ASTM F1717