EndoLab - Implant Testing Services Implant Testing

Hip implants
all procedures accredited

Fatigue Test - ISO 7206-4, ISO 7206-6 and PI-58 (ISO 7206-8)Fatigue Test - ISO 7206-4, ISO 7206-6 and PI-58 (ISO 7206-8) Femoral head torsion test - ISO 7206-13Femoral head torsion test - ISO 7206-13 Femoral Head Compression Test - ISO 7206-10/ ASTM F2345/ PI-14Femoral Head Compression Test - ISO 7206-10/ ASTM F2345/ PI-14 Femoral Head pull-off test - ASTM F 2009Femoral Head pull-off test - ASTM F 2009 Luxation test - PI-3Luxation test - PI-3 Hip surface analysis - ISO 7206-2Hip surface analysis - ISO 7206-2 Hip Wear Test - ISO 14242-1Hip Wear Test - ISO 14242-1 Disassembly Forces of Modular Acetabular Devices - ASTM F1820Disassembly Forces of Modular Acetabular Devices - ASTM F1820 Fretting Corrosion Testing of Modular Implants – Femoral Stem-Head Interface - ASTM F1875Fretting Corrosion Testing of Modular Implants – Femoral Stem-Head Interface - ASTM F1875 Hip Range of Motion – ISO 21535Hip Range of Motion – ISO 21535 Fatigue test - ASTM F 2580Fatigue test - ASTM F 2580 Impingement Test - ASTM F2582Impingement Test - ASTM F2582 Insert Compression Test - PI-11Insert Compression Test - PI-11 Microseparation test - PI-78 (ISO 14242-4)Microseparation test - PI-78 (ISO 14242-4) Third body wear test based on - ISO 14242-1Third body wear test based on - ISO 14242-1 High demand hip wear testing - ASTM F3047MHigh demand hip wear testing - ASTM F3047M Deformation test for acetabular shells - ISO 7206-12Deformation test for acetabular shells - ISO 7206-12 3D Frictional torque measurement of total hip joint prostheses - PI-643D Frictional torque measurement of total hip joint prostheses - PI-64 Guide for assessment of hard-on-hard articulation THR devices - ASTM F3018Guide for assessment of hard-on-hard articulation THR devices - ASTM F3018 Impact Resistance Femoral Heads - ISO 11491Impact Resistance Femoral Heads - ISO 11491 FEA Non-modular Hip Femoral Stem - ASTM F2996FEA Non-modular Hip Femoral Stem - ASTM F2996 Requirements for Femoral Prostheses - Metallic Implants - ASTM F2068Requirements for Femoral Prostheses - Metallic Implants - ASTM F2068 Bearing surface characterization of retrieved hard-on-hard hip prostheses - ...Bearing surface characterization of retrieved hard-on-hard hip prostheses - ASTM F2979 Specific Requirements for Hip-joint Replacement Implants - ISO 21535Specific Requirements for Hip-joint Replacement Implants - ISO 21535 Particular requirements for joint replacement implants - ISO 21534Particular requirements for joint replacement implants - ISO 21534 Fatigue Test of Acetabular Devices - ASTM F3090Fatigue Test of Acetabular Devices - ASTM F3090 Classification and Designation of Dimensions - ISO 7206-1Classification and Designation of Dimensions - ISO 7206-1

Fatigue Test - ISO 7206-4, ISO 7206-6 and PI-58 (ISO 7206-8)

Normative References  



ISO 7206-4: Implants for surgery - Partial and total hip joint prostheses - Part 4: Determination of endurance properties and performance of stemmed femoral components

ISO 7206-6: Implants for surgery - Partial and total hip joint prostheses - Part 6: Endurance properties testing and performance requirements of neck region of stemmed femoral components

PI-58 (ISO 7206-8): Implants for surgery - Partial and total hip joint prostheses - Part 8: Endurance performance of stemmed femoral components

The fatigue test according to ISO 7206-4 simulates the dynamic loading of a hip stem during gait. Proximal loosening of the stem is presumed to simulate worst case conditions and replicates clinical failure. Load inclination, embedding level, load level and number of cycles are given by the test standard. The test conditions do provide safety information about fatigue failure of hip stems by a simplified model.

ISO 7206-6 simulates a well ingrown stem. Fracture (if any) is expected to occur at the neck region of the stem.


The alignment of the hip stem versus the test load is straightforward for simple hip stem geometries but may be challenging for anatomic stems. EndoLab® has developed a 3D CAD based method to design custom AM-printed jigs for sample alignment.

The maximum test frequency depends on the flexibility of the stem and the performance of the test equipment. EndoLab® developed special tools to embed the stem correctly (see Fig.) which ensure constant loading of the implant. Most of our tests are performed using MTS® or Zwick® test equipment.

 

Implant Testing - Fatigue Test - ISO 7206-4, ISO 7206-6 and PI-58 (ISO 7206-8) Fatigue Test - ISO 7206-4, ISO 7206-6 and PI-58 (ISO 7206-8) hip, implant, surgery, implant testing, fatigue testing, fatigue test, prosthesis, prostheses, dynamic loading, hip stem, hip joint, ISO 7206-4, ISO 7206-6, PI-58, ISO 7206-8